(mods: I hope this is the right forum for this thread. Game Hp 320x240 Rifaiy Share. ) I've been trying to set up Cacti to monitor my internet usage, but I can't seem to get it to get the correct data from my router. My router is a Netgear FVS318, which has SNMP support, but I'm having trouble figuring out what are each of the 4 interfaces it shows data transfer stats for, and how they map to the WANLAN data transfer.

Here's a snippet of the output of an snmpwalk: IF-MIB::ifDescr.1 = STRING: lo0 IF-MIB::ifDescr.2 = STRING: mirror0 IF-MIB::ifDescr.3 = STRING: et1 IF-MIB::ifDescr.4 = STRING: ppp0 IF-MIB::ifType.1 = INTEGER: softwareLoopback(24) IF-MIB::ifType.2 = INTEGER: ethernetCsmacd(6) IF-MIB::ifType.3 = INTEGER: ethernetCsmacd(6) IF-MIB::ifType.4 = INTEGER: ppp(23) IF-MIB::ifSpeed.1 = Gauge32: IF-MIB::ifSpeed.2 = Gauge32: 10000000 IF-MIB::ifSpeed.3 = Gauge32: 10000000 IF-MIB::ifSpeed.4 = Gauge32: 19200 here's the full, and here's a screenshot of the from this morning. I figured that interface 4 (listed as type 'ppp') would be the WAN connection, but as you can see in the Cacti graphs, it's not showing all the traffic properly (or at least not what I expected). There's two main things that I can't figure out about these graphs/snmp output: • the 'ppp' interface is listed being connected at 19.2kbps, but I expected either 10Mbps or ~14Mbps (depending on whether the speed between the router and full-bridge modem, or the ADSL connection speed is used) • in the Cacti graphs, it seems that the 'mirror0' interface shows only bittorrent traffic (scheduled stop at 7am, manually run between 9:30am and 11:15am), while 'ppp0' interface shows all other traffic but the scale is completely wrong. Note: the traffic shown for 'mirror0' is also listed back to front, but I figured it was an internal thing to the router, so 'in' and 'out' obviously don't have the same meaning as for the WAN port. This bit's not an issue though, since it's just a labelling fix required. Does anyone have any ideas on how to make Cacti interpret the snmp data properly, so I can get a simple graph of traffic on the WAN side of the router? E1705 Touchpad Driver. (Hopefully you can follow my ramblings) EDIT: Oh, and since someone will probably ask: I'm running Cacti 0.8.7b on Ubuntu Server 8.04.2.

Ellen Von Unwerth Revenge Pdf Printer. Uptime Through Simplicity. You can use the built in “Cisco Router” template that comes by default with cacti. Configure Your HP Procurve Switch with.

But I'm having trouble figuring out what are each of the 4 interfaces it shows data transfer stats for, and how they map to the WANLAN data transfer. A common problem when using SNMP and SNMP tools. Not all stats will make sense, and not all stats across routers will show the right data. Sometime you have no choice but to look at all stats, graph em, and then cut out the useless stuff.

Forget loopback stats – I've never had understandable stats from them. Et1 is a good candidate – it's a physical port (maybe). Ppp – you'll be lucky to get anything useful.

Hp Support Assistant Silent Install Itunes. Sometimes only the physical ports will produce good SNMP/MIB stats, the logical ones just show nothing. Just graph everything you can, and trim out the stuff that doesn't help.